PERMABOND 2011
Harmonization Code : 3506.91.90.99 | Prepared glues and other prepared adhesives, not elsewhere specified or included; products suitable for use as glues or adhesives, put up for retail sale as glues or adhesives, not exceeding a net weight of 1 kg ; Adhesives based on polymers of headings 3901 to 3913 or on rubber; Other ; Other
Main features
- Thixotropic Application Control
- 5 to 10-Second Fixturing Time
- One-Part Moisture-Cure Adhesive
Product Description
PERMABOND® 2011 Cyanoacrylate Adhesive is a single-component, thixotropic ethyl cyanoacrylate developed for rapid bonding on vertical and porous surfaces. Its gel consistency supports controlled application with reduced flow, while moisture on the mating surfaces initiates cure after the parts are pressed together. The colorless adhesive fixtures documented steel, Buna N rubber, and phenolic substrates in 5–10 seconds and reaches full strength after 24 hours. It provides a maximum documented gap-filling capability of 0.5 mm and can be used on metals, plastics, elastomers, ceramics, and wood.
Key features
- Thixotropic gel consistency: Supports controlled application on vertical and porous substrates with a maximum documented gap fill of 0.5 mm.
- Rapid fixture performance: Reaches 0.3 N/mm² shear strength in 5–10 seconds on documented steel, Buna N rubber, and phenolic substrates.
- Single-component moisture-initiated cure: Requires no component mixing and develops full strength after 24 hours under documented conditions.
Applications / Suitable for
- Bonding vertical and porous substrates
- Bonding metals, plastics, and elastomers
- Bonding ceramics and wood
- Rapid assembly of components with gaps up to 0.5 mm
Technical Specifications
General Properties
Physical Properties
Electrical Properties
Additional Information
As-supplied / before-processing properties
Typical as-supplied and cure-stage properties of PERMABOND® 2011. The technical data sheet identifies these values as guideline information rather than specifications.
| Property | Value | Unit | Method / condition |
|---|---|---|---|
| Chemical composition | Ethyl cyanoacrylate | — | Single-component adhesive |
| Appearance | Colorless | — | As supplied |
| Viscosity | Gel | — | At 25°C |
| Specific gravity | 1.1 | — | Typical |
| Maximum gap fill | 0.5 (0.02) | mm (in) | Documented maximum gap-filling capability |
| Fixture / handling time | 5–10 | seconds | Time to achieve 0.3 N/mm² shear strength on steel, Buna N rubber, or phenolic |
| Full-strength time | 24 | hours | Cure speed can vary with temperature, humidity, substrate, surface acidity, and gap |
| Storage temperature | 2–7 (35–45) | °C (°F) | Allow the adhesive to reach room temperature before opening |
After-processing / final-state properties
Typical cured-material and substrate-specific performance data. Bond-strength results vary with surface preparation and joint gap and are not product specifications.
| Property | Value | Unit | Method / condition |
|---|---|---|---|
| Shear strength on steel | 20–24 (2,900–3,500) | N/mm² (psi) | ISO 4587 |
| Shear strength on aluminum | 8–9 (1,200–1,300) | N/mm² (psi) | ISO 4587 |
| Shear strength on ABS | >8 (>1,200) | N/mm² (psi) | ISO 4587; substrate failure |
| Shear strength on PVC | >10 (>1,450) | N/mm² (psi) | ISO 4587; substrate failure |
| Impact strength | 3–5 (1.4–2.4) | kJ/m² (ft·lb/in²) | ASTM D-950 |
| Hardness | 85 | Shore D | ISO 868 |
| Dielectric strength | 25 | kV/mm | Typical cured-material property |
| Thermal conductivity | 0.1 | W/(m·K) | Typical cured-material property |
